Virtual Guide
Perform all your agricultural operations with greater precision and efficiency, with intelligent GPS-guided navigation.
Benefits
Easy to operate
Can be installed on any machine
Maintenance of initial investment
Low obsolescence rate
Better control of applications, machines and operators
Adequacy to operational needs
It is possible to pre-determine the area where you will work
Greater durability and resistant to high temperatures and chemicals, overloads, short circuit or improper connections
One of the most common jobs in the field has now become much easier!
ISO 30 works as a virtual guide, which will control the layout of the machines in your cultivation area, navigating in parallel paths, regardless of whether the route starts on a straight or curve, requiring only one start point and another end.
The system allows diverse field operations to be carried out, such as preparing the soil, planting seeds, cultivating the plantation and harvesting the crops. Thus, with the information generated and stored in ISO 30, you can manage your entire agricultural operation in a more effective and strategic way, in order to improve your productivity.
- Navigation on straight or curved parallel lines
- Control of break points and activity restart
- Recording of routes and maps of areas covered
- Real-time calculation of areas covered by the machine
- Record speed, distance and operating time
- Importing the guides project
- Storage and downloading of all recorded data
- Model: IsoView 30
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter (optional upgrade)
- GNSS: GPS / GLONASS L1 10 Hz Module
- On-board computer 7 ”touch - IsoView IsoPoint 1
- Guide control license - IsoGuide
- Antenna L1 / L2 / L-Band GPS / GLONASS
- Power Cabling
- Antenna cabling
- Suction cup
Coming soon!
Autopilot
The highest precision in agricultural navigation, resulting in less soil compaction, greater operational efficiency and a lot of comfort.
Benefits
Compatible with power steering tractors
Compatible with a wide variety of predisposed and non-predisposed tractors
Installation as fast as an electric pilot
Higher precision, greater efficiency, less component wear
Greater durability and lower maintenance cost
Superior layout compared to the electric model, also guaranteeing greater safety in the operation
Increased safety in emergencies
Ensures greater accuracy and fault detection
Simpler and more agile work start
Meets the main job options
Accurately work on any type of terrain, flat or inclined
Availability of more accurate signal corrections through service or product options
A complete system for agricultural navigation!
This is ISO 33, a virtual guide combined with autopilot, which guarantees greater profitability of operations in the field. With decimetric precision (IsoPoint 2), the system has updates available that allow reaching up to centimeter accuracy (IsoPoint 3 and 4).
Fundamental to the control of machines in a cultivation area, ISO 33 performs navigation on parallel paths, guided by GPS, which makes possible several field operations, such as soil preparation, planting of seeds, cultivation of the plantation and the crop harvest.
The system can be used in tractors and self-propelled, predisposed or not, that is, regardless of the presence of hydraulic preparation for autopilot.
With the information generated and stored during the operation, you can more effectively manage your strategic decisions in the field, and consequently increase your productivity.
- Automatic steering on straight or curved parallel lines
- Hydraulic cylinder steering valve control
- Slope compensation for rough terrain
- Trip by touch detection on the steering wheel or by pedal
- Wheel angle sensor for greater accuracy and fault diagnosis
- Calibration setting for each machine type
- Centimeter accuracy available through paid signal (IsoPoint 3) and RTK signal (IsoPoint 4)
- Model: IsoView 33
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter (optional upgrade)
- GNSS: Module GPS / GLONASS L1 / L2 / L-Band 10 Hz
- External module: 3-axis terrain compensator
- On-board computer 7 ”touch - IsoView IsoPoint 2
- Guide control license - IsoGuide
- Autopilot (PA) license - IsoPilot
- Antenna L1 / L2 / L-Band GPS / GLONASS
- PA ECU with ground compensator - IsoBox
- Steering ECU - IsoBox
- Power Cabling
- PA cabling
- Antenna cabling
- Wheel sensor
- PA trip sensor
- Hydraulic block *
- Hydraulic hoses and connections *
- Suction cup
* For model not predisposed
Coming soon!
Spray control
Ensure an application of liquid inputs in the ideal amount for each part of the field, increasing your productivity and avoiding overlaps.
Benefits
Can be installed on any equipment
Low obsolescence rate
Easy return from the activity started
No need for additional equipment, simplified operation and operator attention directed to a single activity
Better control of applications, machines and operators
Compatible with all types of sprayers
Compatible with the main command brands in the market
Configuration of pre-registered nozzles or option to insert new standards
Economy guarantee, with multiple versions of application and work control
Various spray boom division configurations, without the addition of external modules
Optimization and savings in structured applications using recommendation maps
The application of liquid inputs is one of the most critical stages of the cultivation process. And now, with a touch of technology, she gains more precise and integrated control.
The spray controller regulates the flow of application of the input according to the dosage prescription map loaded in the memory, or it can follow a fixed value programming carried out by the operator himself.
ISO 31 can be used in several types of sprayers, such as self-propelled, coupled or dragged, configured with flow meter, regulating valve, general valve and up to 9 2 or 3 wire section valves. When used in conjunction with the automatic section cut permit, the system avoids overlapping applied areas. All configurations are possible in an integrated manner, that is, without the addition of external components.
The system also functions as a virtual guide, which will control the layout of the machines in your cultivation area, navigating in parallel paths, regardless of whether the route starts on a straight or curved path, requiring only one starting point and another end.
- Flow calculation according to machine speed (Optional)
- Flow flow regulation with programmed fixed dosage
- Processing of variable dosage application maps (Optional)
- Proportional flow control valve
- Configuration of different types of valves, nozzles and inputs
- Control of spray section shutoff valves
- Automatic section cutting in the applied area overlay (Optional)
- Model: IsoView 31
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter
- GNSS: GPS / GLONASS L1 10 Hz Module
- On-board computer 7 ”touch - IsoView
- Guide control license - isoguide
- Spray control license - IsoSpray
- L1 GPS / GLONASS antenna - IsoPoint 1
- Power Cabling
- Spray cabling
- Suction cup
Coming soon!
Spray control with autopilot
Ensure an application of liquid inputs in the ideal amount for each part of the field, increasing your productivity and avoiding overlaps.
Precision spraying in agricultural navigation!
The spray controller regulates the flow of application of the input according to the dosage prescription map loaded in the memory, or it can follow a fixed value programming carried out by the operator himself.
This equipment can be used in self-propelled sprayers, coupled or dragged, predisposed or not, that is, regardless of the presence of hydraulic preparation for automatic pilot, and configured with flow meter, regulating valve, general valve and up to 9 valves of section 2 or 3 wires. When used in conjunction with the automatic section cut permit, the system avoids overlapping applied areas. All configurations are possible in an integrated manner, that is, without the addition of external components.
The ISO 32 autopilot represents the most advanced navigation technology based on acceleration and angle data processing on various spatial axes, and information received from global positioning satellites. As a result, the system performs the actuation of valves that are directly connected in the hydraulic direction of the machine, which guarantees greater precision and reliability in the operation.
The system also functions as a virtual guide, which will control the layout of the machines in your cultivation area, navigating in parallel paths, regardless of whether the route starts on a straight or curved path, requiring only one starting point and another end.
Spraying
- Flow calculation according to machine speed (optional)
- Flow flow regulation with programmed fixed dosage
- Processing of variable dosage application maps (optional)
- Proportional flow control valve
- Configuration of different types of valves, nozzles and inputs
- Control of spray section shutoff valves
- Automatic section cutting in the applied area overlay (optional)
Autopilot
- Automatic steering on straight or curved parallel lines
- Hydraulic cylinder steering valve control
- Slope compensation for rough terrain
- Trip by touch detection on the steering wheel or by pedal
- Wheel angle sensor for greater accuracy and fault diagnosis
- Calibration setting for each machine type
- Centimeter accuracy available through paid signal (IsoPoint 3) and RTK signal (IsoPoint 4)
- Model: IsoView 32
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter
- GNSS: Module GPS / GLONASS L1 / L2 / L-Band 10 Hz
- External module: 3-axis terrain compensator
- On-board computer 7 ”touch - IsoView IsoPoint 2
- Guide control license - IsoGuide
- Spray control license - IsoSpray
- Autopilot (PA) license - IsoPilot
- Antenna L1 / L2 / L-Band GPS / GLONASS
- PA ECU with ground compensator - IsoBox
- Steering ECU - IsoBox
- Power Cabling
- Spray cabling
- PA cabling
- Antenna cabling
- Wheel sensor
- PA trip sensor
- Hydraulic block *
- Hydraulic hoses and connections *
- Suction cup
* For model not predisposed
Coming soon!
Fertilization control
Have the utmost precision and care in preparing the soil, distributing in each small fraction of soil only the appropriate and necessary amount of fertilizer.
Benefits
Compatible with the wide variety of distributors on the market
Compatible with predisposed and non-predisposed distributors
Greater precision in the distribution of fertilizers
Allows the farmer to modernize his distributor while spending little
Economy with non-overlapping applications
Distribution with precise and uniform dosing
Savings in structured applications using recommendation maps
Optimized accuracy through calibration for each input
Advanced optimization for hatch section cut-out dispensers
Technology and precision in the application of solid inputs in your crops!
ISO 34 is a complete system for carrying out this very important task in the field. The system ensures that each fraction of the soil receives the appropriate amount of fertilizer as prescribed.
The fertilization controller calculates, in real time, the application rate in units of weight per covered area, controlling the valves that control the handling and spreading of solid inputs.
In addition, ISO 34 has the ability to turn off distribution in an area that has already been covered. The variable rate control is performed by inserting a prescription map, with variable dosages within the same work area.
It can be used in self-propelled, coupled or dragged, mat or gravitational distributors, prepared or not, that is, regardless of the presence of hydraulic or electrical preparation for the distribution, and configured with the control of the mat, discs and gate.
The system also functions as a virtual guide, which will control the layout of the machines in your cultivation area, navigating in parallel paths, regardless of whether the route starts on a straight or curved path, requiring only one starting point and another end.
- Automatic shutdown of distribution in the applied area overlay
- Dosing compensation according to machine speed
- Speed regulation of spreading discs
- Processing of variable dosage application maps (Optional)
- Proportional control of conveyor valve;
- Calibration of volume and weight of different types of inputs
- Gate trigger control (Optional)
- Model: IsoView 34
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter (optional upgrade)
- GNSS: GPS / GLONASS L1 10 Hz Module
- External module: Track and disc control
- On-board computer 7 ”touch - IsoView IsoPoint 1
- Guide control license - IsoGuide
- Fertilization control license - IsoSpread
- Antenna L1 / L2 / L-Band GPS / GLONASS
- Fertilization control ECU - IsoBox
- Power Cabling
- Fertilization cabling
- Inductive sensors for track and disc speed
- Track speed encoder (optional)
- Electric actuators *
- Hydraulic engine*
- Line filter *
- Hydraulic block *
- Hoses and fittings *
- Suction cup
* For unprepared model
Coming soon!
Fertilization control with
autopilot
Have the utmost precision and care in preparing the soil, distributing in each small fraction of soil only the appropriate and necessary amount of fertilizer.
A complete system for the application of solid inputs, which ensures that each fraction of the soil receives the appropriate amount of fertilizer as prescribed, and with automated coverage.
The fertilization controller calculates, in real time, the application rate in units of weight per covered area, controlling the valves responsible for handling and spreading the solid inputs. And don't worry about overlapping applied areas: ISO 35 has the ability to turn off distribution in an area already covered.
It can be used in self-propelled, coupled or dragged, mat or gravitational distributors, prepared or not, that is, regardless of the presence of hydraulic or electrical preparation for the distribution, and configured with the control of the mat, discs and gate.
The ISO 35 autopilot represents the most advanced navigation technology based on acceleration and angle data processing on various spatial axes, and information received from global positioning satellites. As a result, the system performs the actuation of valves that are directly connected in the hydraulic direction of the machine, which guarantees greater precision and reliability in the operation.
The system also functions as a virtual guide, which will control the layout of the machines in your cultivation area, navigating in parallel paths, regardless of whether the route starts on a straight or curved path, requiring only one starting point and another end.
Spreading
- Automatic shutdown of distribution in the applied area overlay
- Dosing compensation according to machine speed
- Speed regulation of spreading discs
- Processing of variable dosage application maps (optional)
- Proportional control of conveyor valve;
- Calibration of volume and weight of different types of inputs
- Gate trigger control (optional)
Autopilot
- Automatic steering on straight or curved parallel lines
- Hydraulic cylinder steering valve control
- Slope compensation for rough terrain
- Trip by touch detection on the steering wheel or by pedal
- Wheel angle sensor for greater accuracy and fault diagnosis
- Calibration setting for each machine type
- Centimeter accuracy available through paid signal (IsoPoint 3) and RTK signal (IsoPoint 4)
- Model: IsoView 35
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter (optional upgrade)
- GNSS: Module GPS / GLONASS L1 / L2 / L-Band 20 Hz
- External module: Track and disc control
- External module: 3-axis terrain compensator
- On-board computer 7 ”touch - IsoView
- Guide control license - isoguide
- Fertilization control license - isospread
- Autopilot license (PA) - isopilot
- Antenna L1 / L2 GPS / GLONASS - IsoPoint 2
- Fertilization control ECU - isobox
- PA ECU with terrain compensator - isobox
- Steering ECU - isobox
- Power Cabling
- Fertilization cabling
- PA cabling
- Antenna cabling
- Inductive sensors for track and disc speed
- Track speed encoder (Optional)
- Electric actuators *
- Hydraulic engine*
- Line filter *
- Hydraulic blocks *
- Hoses and fittings *
- Suction cup
* For model not predisposed and not prepared
Coming soon!
Planting monitor
It has never been easier to monitor your productivity, and still ensure comfortable and accurate navigation.
Agricultural navigation, now with integrated planting monitor!
Unlike traditional solutions, the planting monitor not only monitors the drop of seeds detected by sensors present in each planting line of the machine, but also performs the seed count. Integrated with the virtual guide navigation, it allows you to control the layout of the machines in your cultivation area, navigating in parallel paths, regardless of whether the route starts in a straight line or curve, requiring only one start and end point.
ISO 36 can also calculate in real time the distance between the seeds deposited in the soil, which can vary according to the speed of the machine, to inform the operator of the acceleration that must be applied to maintain the population per linear meter. In addition, alarms are generated that instantly show the absence of a fall, or even the deposition of more than one seed at a given point.
The equipment records in memory a map of the planted area, in addition to a report of statistical data, so that it is possible to manage the entire planting process carried out.
- Calculation of distance between seeds in the planting line
- Instant diagnosis and alarm of sowing failures
- Seed count for population registration
- Speed monitoring for suitable population
- Processing reports and planting maps in memory
- Simple and efficient calibration process
- Expandable system for up to 64 sensors
- Model: IsoView 36
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter (optional upgrade)
- GNSS: GPS / GLONASS L1 10 Hz Module
- Seed sensors: Intelligent optical reader with CAN communication
- On-board computer 7 ”touch - IsoView IsoPoint 1
- Guide control license - IsoGuide
- Planting monitor license - IsoSeed
- Antenna L1 / L2 / L-Band GPS / GLONASS
- Planting ECU every 10 rows - IsoBox *
- Power Cabling
- Planting cabling
- Planting sensor for each row
- Suction cup
* Optional for market analogue sensors
Coming soon!
Planting monitor with autopilot
It has never been easier to monitor your productivity, and still ensure comfortable and accurate navigation.
Agricultural navigation, now with integrated planting monitor!
Unlike traditional solutions, the planting monitor not only monitors the drop of seeds detected by sensors present in each planting line of the machine, but also performs the seed count. Integrated with the virtual guide navigation, it allows you to control the layout of the machines in your cultivation area, navigating in parallel paths, regardless of whether the route starts in a straight line or curve, requiring only one start and end point.
ISO 37 can also calculate in real time the distance between the seeds deposited in the soil, which can vary according to the speed of the machine, to inform the operator of the acceleration that must be applied to maintain the population per linear meter. In addition, alarms are generated that instantly show the absence of a fall, or even the deposition of more than one seed at a given point.
The ISO 37 autopilot represents the most advanced navigation technology based on acceleration and angle data processing on various spatial axes, and information received from global positioning satellites. As a result, the system performs the actuation of valves that are directly connected in the hydraulic direction of the machine, which guarantees greater precision and reliability in the operation.
The equipment records in memory a map of the planted area, in addition to a report of statistical data, so that it is possible to manage the entire planting process carried out.
Seeding
- Calculation of distance between seeds in the planting line
- Instant diagnosis and alarm of sowing failures
- Seed count for population registration
- Speed monitoring for suitable population
- Processing reports and planting maps in memory
- Simple and efficient calibration process
- Expandable system for up to 64 sensors
Piloto Automatic
- Automatic steering on straight or curved parallel lines
- Hydraulic cylinder steering valve control
- Slope compensation for rough terrain
- Trip by touch detection on the steering wheel or by pedal
- Wheel angle sensor for greater accuracy and fault diagnosis
- Calibration setting for each machine type
- Centimeter accuracy available through paid signal (IsoPoint 3) and RTK signal (IsoPoint 4)
- Model: IsoView 37
- Processor: 180MHz
- Internal Memory: 64MB
- Storage: 8GB
- Screen: 7 Inches
- Resolution: 800 x 480
- Communication: 2x CAN channels for communication with application ECUs and autopilot
- Inputs / Outputs: Control of up to 9 sections, regulating valve, general valve and flow meter (optional upgrade)
- GNSS: Module GPS / GLONASS L1 / L2 / L-Band 10 Hz
- Seed sensors: Intelligent optical reader with CAN communication
- External module: 3-axis terrain compensator
- On-board computer 7 ”touch - IsoView IsoPoint 2
- Guide control license - IsoGuide
- Fertilization control license - IsoSpread
- Autopilot (PA) license - IsoPilot
- Antenna L1 / L2 / L-Band GPS / GLONASS
- Fertilization control ECU - IsoBox
- PA ECU with ground compensator - IsoBox
- Steering ECU - IsoBox
- Power Cabling
- Fertilization cabling
- PA cabling
- Antenna cabling
- Inductive sensors for track and disc speed
- Track speed encoder (optional)
- Electric actuators *
- Hydraulic engine*
- Line filter *
- Hydraulic blocks *
- Hoses and fittings *
- Suction cup
* For model not predisposed and not prepared
Coming soon!